Wednesday 04 July, 2018 | RSS Feed

Repair iPhone 6S Headset Jack Does Not Work

When traveling or shopping alone, music is the best companion. When the hands are busy, the call needs the help of the headphones. If the headphone interface is broken, it will bring us unnecessary troubles. I believe that many people have encountered situations where the iPhone 6s plugged into the headset and did not respond. For example, headphones are not recognized, there is no sound when listening to music, watching videos, and so on. What should we do if the earphone jack of the iphone 6s has no sound? How to repair it? In this article, our phonefix shop team will bring you the answer.





First of all, find another phone and plug in the headset to see if the headset will make a sound. If it is, it is a problem with the phone itself. If it is not a problem with the headset, just replace the new headset to solve the problem.

Restart your iPhone

To test potential software issues, try restarting the iPhone. Turning off and re-opening the iPhone can sometimes solve small software problems because all programs running on the iPhone can be automatically shut down and restarted. Press and hold the On/Off button and release the power button when the Apple logo appears in the center of the iPhone display. Let the phone restart.

Check AirPlay output

One reason audio may not play through headphones is that your iPhone is sending audio to another output.The iPhone is supposed to automatically recognize when headphones are plugged in and switch the audio to them, but it's possible that that hasn't happened in your case. One potential reason is that the audio is sent to an AirPlay compatible speaker or AirPods. So you can check for that:

- Swipe up from the bottom of the iPhone screen to open the Control Center (on iPhone X, swipe down from the top right corner).
- Press and hold the music playback control in the upper right corner of the Control Center.
- Click the AirPlay button in the upper right corner of the music control to display all available output sources.
- Tap the headset.
- Click the screen or click the iPhone home button to close the Control Center.
- After changing these settings, your iPhone audio will now be sent to the headset.



Clear the headphone hole

1. The lint, trash and other debris stuck in the headphone jack may prevent the iPhone from recognizing the inserted headphones. If the headphone jack does not work on the iPhone, use an antistatic brush to clean the headphone jack.

2. Dip the alcohol with a cotton swab, squeeze it clean, insert the cotton swab into the hole of the earphone and turn it out again and then pull it out several times. Be careful not to break the cotton swab with too much force.


Update to the latest iOS version available.

Apple typically addressed apparent device issues by rolling out software updates that contain bug fixes. You might as well give this a shot this time. Just be sure to back up your iPhone to iCloud/iTunes before you perform an upgrade. That way you will still be able to restore from a backup should the upgrade does no good to your iPhone. To check for available software updates for your iPhone, go to Settings-> General-> Software update. Follow the onscreen instructions to complete the update process, if available.


If the above steps do not solve the problem, there may be a hardware problem with your iPhone, you need to replace the iPhone6 headphone jack. Lift the Lightning connector and the headphone jack cable and remove it from the iPhone. Before installing or replacing the Lightning connector assembly : Use a plastic tool to flush any residue from the back shell behind the cable.

If you encounter any problems during the repair of your mobile phone, please do not hesitate to contact us on www.vipfixphone.com.


by VIPFIXPHONE




How to Repair Cell Phone Low Voltage Alarm Fault

The low voltage alarm failure in the mobile phone repair refers that even if the normal battery is installed, the mobile phone still shows the low battery power or the power is not full. How to test and repair this common situation? In this article, phonefix shop team will offer some specific methods on different phone models, there are some examples of the low voltage alarm are briefly analyzed. Hope the article will help you!





In order to repair the low voltage alarm failure, we must first understand the mechanism of the low voltage alarm. In fact, the mechanism of the low voltage alarm failure is very simple. It is realized by detecting the battery power. If it's iPhone, then it's the frist step to detect the iPhone battery.

After the voltage VBAT of the battery is divided into two resistors Rl and R2, the sample is sent to the digital analog conversion (A/D) circuit, the analog signal is converted to the digital signal and sent to the CPU, and then the CPU from the code is called the parameter of the battery power (the program is set well). The CPU can be determined by comparing the data set in the A/D and the predetermined data in the chip by comparing the A/D. The current supply voltage level, and then CPU according to the comparison results, sent to the display to display the battery's current power. 

If the battery power is smaller than the low power alarm parameters, CPU will display the power of the display to be empty, at the same time, send a low alarm signal, and then automatically turn off. In actual circuit, A/D converter is not set separately, it is usually integrated in cell phone power management IC,  CPU or audio processing lC.

According to the previous analysis, there are several reasons for low power alarm failures.

1. filter capacitor Cl leakage will lead to the reduction of voltage after the partial pressure, that is, the actual voltage after the sampling is reduced, so that the CPU is mistaken for the reduction of the battery voltage, thus causing a low alarm failure. As long as the Cl is dismantled.

2. higher voltage resistance Rl resistance increases, or lower voltage resistance R2 resistance decreases, the actual voltage after sampling is reduced, resulting in low alarm failure. At this time, as long as the proper adjustment of the Rl, R2 resistance can be.

3. since the battery voltage is sent to CPU by resistance partial pressure and A/D conversion, if the A/D converter is abnormal, it will cause low power alarm.

4. if the low alarm threshold voltage of the software is too high, a low voltage alarm fault will also occur. When overhauling, it is only necessary to rewrite the correct data.

5. if the battery supply load circuit such as power amplifier has large leakage current, it will lower the battery voltage, resulting in low power alarm.

6. if the contact piece of the battery is blackened, it will make the battery contact piece produce larger internal resistance, which is equivalent to increasing the upper voltage divider.



Therefore, after A/D conversion and CPU detection, it will cause low power alarm failure. When a low power alarm fault is maintained, a small file or sandpaper can be used.

Clean the contact thoroughly. Sometimes, bad battery will also appear to call or battery to use for a long time, that is, low power alarm failure.

If you have any other problems for cell phone repair, please get technical support from China Phonefix Shop Team on www.vipfixphone.com


by CNFIXPHONE




Introduction for Parts of A Smartphone

What parts are there inside your cell phone? If no, you may be interested in the next happening. Either DIY lover or phone repair technicians need to know what spare parts are there in any mobile phone or smartphone, becuase it will be helpful during the repair process. Actually, these spare parts almost are the same in all smartphone as well as tablets, like Apple, Samsung, Huawei, HTC, ZTE, LG etc. the difference may be that only the shape and size of the parts. Each parts plays an important role in phone function performance, but the same parts plays the same function. Here our Phonefix team will share a detail inftroduction for phone parts.


 

According to we know, there are types of parts in all cell phones: external parts and internal parts.

 

1 External parts:

 

The external parts consist of snap on covers (casing) which can be detached and replaced by hand with the help of phone opening tools. 

 

2 Internal parts

 

PCB Circuit Board: The green or blue coloured board inside a cell phone is called the PCB , which is also called motherboard, it is the most important part in a cell phone. All the ICs which perform various functions are fixed on this circuit boatd, all the parts need to reply on this board. We can call it engine for a car.

 

Tips: the inteligence phone motherboard fixture will be useful for its repair.

Battery: It supplies power to the cell phone. For most phone battery, it can be easier removed after removing the back cover, but it may ask some professional phone disassemble tools. The output voltage of a cell phone battery is either 3.7V DC or 3.8V DC.

 

Mic: It is also called microphone and mouth piece. It converts voice into electrical signal. Its function is to send our voice to the called person. It will always be at the buttom inside a cell phone.

 

Speaker: It is aslo called earpiece and receiver, used to receive call and get the access to Siri. Usually it always be at the top inside a cell phone.

 

Ringer: A ringer is also called a buzzer or loud speaker. It is a speaker with which we hear the ringtones and music and all the sounds which we hear louder.

 

Vibrator: A vibrator is also called vibration motor and vibra motor. It is a DC motor which creates vibration when it rotates. The vibration in the handset when we receive a call is due to this part.

 

Keypad: Its function shows on-off switch, when we press the buttons, its two connectors contact with each other and the button functions.

 

Antenna: Its function is to receive and transmit the signals. Now all models have antennas that are inbuilt and hence not visible from outside. In old phones, antennas were external and hence were visible.

 

LCD Display: Almost all the smartphone are equipped with LCD screen, which is called as display. At the same time, it is the most weak among all the internal parts.

 

Touch: It is a transparent part, above the LCD which allows the touch function to work. In most models now, the LCD and touch are fused together into one part.

 

Flex: Flex is a brownish golden coloured cable which is used for connecting parts. Its not used in all cell phones. It is used for connecting either LCD, touch or camera to the PCB.

 

Tips: if there happens some faults on flex, what we used mostly is U2 Micro Dock Flex Board.

Battery Connector: It connects the battery to the PCB of the mobile phone. It is the part that transfers the voltage from the battery to the PCB.

 

SIM Connector: It connects the SIM card to the PCB of the cell phone. Sometimes if you found your signal is weak, maybe you eject the SIM card, plug it again to check whether there happens somef faults.

 

Charging connector: This parts need you to disassemble the device, otherwise you can't see it, which can transfer the voltage, so it can't be explosed outside.

 

Earphone Connector: We insert the earphone into this part. 


Though it looks small, it owns a power strength, power function, and equipped with thouands of components. We have listed most of commonly parts when we repaired iPhone faults, so after we saw this article, we advise you do the operation on professional phone repair mat, which can ensure you will not miss the parts during you fixed the faults.

 

Anyway, if you have any other more good ideas, please contact us on www.vipfixphone.com.
 


by CNFIXPHONE





News for Tuesday 03 July, 2018


View all news for Tuesday 03 July, 2018 on one page




Recent News




News archive